Forum | Message

Thu, November, 7th 2019

Forum Question/Topic:

Article:

RF Mesh firmware 9.1 and Yukon 7.3 are now available!

Categorized as:

Consider upgrading your network firmware and Yukon software versions to take advantage of our latest features and improvements. As a reminder, these upgrades are included at no additional cost with your annual maintenance package!

Here are just a few of the new features in Yukon v7.3, FW v9.1, and FW v9.0 (included here due to its limited installations). Many of the listed FW features are combined engineering efforts with Yukon and require the correct Yukon versions as well, so  Read more...we recommend upgrading all the way to Yukon v7.3 before the upgrade to FW v9.1.

Yukon 7.3
• Comprehensive mapping showing nodes by primary gateway or link quality
• Option for the CIS to update device GPS coordinates via MultiSpeak
• Battery Node Analysis Report to identify end-of-life batteries
• Demand response using disconnect meters for a single device to both meter and control sub-metered loads

RF Mesh Firmware 9.1
• Advanced Tamper Detection
• Badger Water Events
• Support of Yukon Device Configuration improvements for polyphase meters
• Meter disconnect status is now provided in the initial data report to help ensure data synchronization
• Additional metrics supported for polyphase meters

RF Mesh Firmware 9.0
• IPv6 support across the RF Mesh down to end nodes
• Anycast and other significant outage improvements for much higher last gasp and restoration alarm success rates (ask about our new recommended timing settings for outage/restoration alarms)
• Improved reliability of clearing outage and OV/UV events appropriately
• Additional metrics supported for polyphase meters
• Yukon Device Configuration scalability improvements allow configuration of larger numbers of meters at once
• Yukon Device Configuration support to change the Demand Interval in single phase meters using Eaton's Advanced Metrology
• Wired gas node support and the RFG-201 Yukon device type

The latest firmware release has been closely monitored in limited deployments over the last three months and is ready for your upgrade. Contact our Technical Services team today to learn more and plan your upgrades! Show less...
AMI
Yukon
Consider upgrading your network firmware and Yukon software versions to take advantage of our latest features and improvements. As a reminder, these upgrades are included at no additional cost with your annual maintenance package! Here are just a few of the new features in Yukon v7.3, FW v9.1, and FW v9.0 (included here due to its limited installations). Many of the listed FW features are combined engineering efforts with Yukon and require the correct Yukon versions as well, so we recommend upgrading all the way to Yukon v7.3 before the upgrade to FW v9.1. Yukon 7.3 • Comprehensive mapping showing nodes by primary gateway or link quality • Option for the CIS to update device GPS coordinates via MultiSpeak • Battery Node Analysis Report to identify end-of-life batteries • Demand response using disconnect meters for a single device to both meter and control sub-metered loads RF Mesh Firmware 9.1 • Advanced Tamper Detection • Badger Water Events • Support of Yukon Device Configuration improvements for polyphase meters • Meter disconnect status is now provided in the initial data report to help ensure data synchronization • Additional metrics supported for polyphase meters RF Mesh Firmware 9.0 • IPv6 support across the RF Mesh down to end nodes • Anycast and other significant outage improvements for much higher last gasp and restoration alarm success rates (ask about our new recommended timing settings for outage/restoration alarms) • Improved reliability of clearing outage and OV/UV events appropriately • Additional metrics supported for polyphase meters • Yukon Device Configuration scalability improvements allow configuration of larger numbers of meters at once • Yukon Device Configuration support to change the Demand Interval in single phase meters using Eaton's Advanced Metrology • Wired gas node support and the RFG-201 Yukon device type The latest firmware release has been closely monitored in limited deployments over the last three months and is ready for your upgrade. Contact our Technical Services team today to learn more and plan your upgrades!
Delivered Read
Eve Richardson, William Arnlund, Brad Lingen like this.

Online